Motherboard: Difference between revisions
(New at www.free60.org) |
imported>Tuxuser m (Text replace - "Category:Hardware" to "Category:Xbox360_Hardware") |
||
| (5 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
{{Cleanup}} | |||
is not the | (This page is riddled with speculation and extrapolation of information from dodgy sources, so take it with a grain of salt.) | ||
The Xbox 360 motherboard (or motherboard) has undergone a few revisions, as Microsoft has corrected mistakes or added/improved existing features. | |||
*Known revisions include: | |||
:*[[Xenon_(Motherboard)|Xenon]] (Launch hardware) | |||
:*[[Zephyr]] (Elite) | |||
:*[[Falcon]] (65nm Chipset revision) | |||
:*[[Opus]] | |||
:*[[Jasper]] (Onboard Memory Unit) | |||
:*[[Trinity]] (Slim) | |||
== Details == | |||
The motherboard PCB has four layers (sources: [http://www.ccw.com.cn/notebook/pczx/sy/htm2005/20051028_16OMI.htm], [http://www.anandtech.com/video/showdoc.aspx?i=2414]), implying that the top and bottom layers (the ones we can see and probe) contain most of the signals. This is a good thing :) | |||
== CPU, GPU, & Front side bus == | |||
According to [http://www.ccw.com.cn/notebook/pczx/sy/htm2005/20051028_16OMI.htm these] [http://www.cdrinfo.com/images/uploaded/Xbox_Architecture_large.gif three] [http://en.wikipedia.org/wiki/Xbox_360#Hardware_specifications sources] the FSB is a serial bus with 16 differential pairs in each direction, and each pair runs at 5.4Gbit/s. This agrees with Microsoft's published bandwidth specification of 21.6 Gbyte/sec (10.8 Gbyte/sec each way, 16 bits/2 bytes at a time, 5.4 Gbit/sec per pair). | |||
Looking at photos of the motherboard, we can see 40 pairs of carefully routed tracks between the CPU and GPU. 32 pairs (16 each way) + 8 clock/handshake/parity? pairs = 40 pairs. | |||
This very high frequency interface will make probing and snooping on the bus extremely difficult, which is unfortunate because the Xbox1 security was compromised in part by a FSB bus snoop done by bunnie. At this frequency, the (relatively) simple task of attaching probe wires to the FSB will change the impedance seen on the bus by the FSB PHYs and cause the bus to fail to work correctly (look at eye diagram...). It might still be possible to probe the FSB with very expensive gear though. | |||
It's not very likely that they made the mistake of sending sensitive information on an exposed bus again though. | |||
== Photos == | |||
*http://arstechnica.com/articles/paedia/cpu/xbox360-1.ars | |||
*http://g-prime.net/x360/open/ | |||
*http://www.darkmoon.org/xbox360_photos.htm | |||
[[Category:Xbox360_Hardware]] | |||
Latest revision as of 00:24, 7 January 2014
 |
This page needs to be cleaned up, because its either hard to read or contains very little information. You can help Free60 by editing this page and cleaning it up. |
(This page is riddled with speculation and extrapolation of information from dodgy sources, so take it with a grain of salt.)
The Xbox 360 motherboard (or motherboard) has undergone a few revisions, as Microsoft has corrected mistakes or added/improved existing features.
- Known revisions include:
Details
The motherboard PCB has four layers (sources: [1], [2]), implying that the top and bottom layers (the ones we can see and probe) contain most of the signals. This is a good thing :)
CPU, GPU, & Front side bus
According to these three sources the FSB is a serial bus with 16 differential pairs in each direction, and each pair runs at 5.4Gbit/s. This agrees with Microsoft's published bandwidth specification of 21.6 Gbyte/sec (10.8 Gbyte/sec each way, 16 bits/2 bytes at a time, 5.4 Gbit/sec per pair).
Looking at photos of the motherboard, we can see 40 pairs of carefully routed tracks between the CPU and GPU. 32 pairs (16 each way) + 8 clock/handshake/parity? pairs = 40 pairs.
This very high frequency interface will make probing and snooping on the bus extremely difficult, which is unfortunate because the Xbox1 security was compromised in part by a FSB bus snoop done by bunnie. At this frequency, the (relatively) simple task of attaching probe wires to the FSB will change the impedance seen on the bus by the FSB PHYs and cause the bus to fail to work correctly (look at eye diagram...). It might still be possible to probe the FSB with very expensive gear though.
It's not very likely that they made the mistake of sending sensitive information on an exposed bus again though.